In Torque Pro app is a plug-in to use the PID of the SKYACTIV-D for vehicles equipped with Mazda.
App requirements
Torque Pro (paid version)
how to use
(1) Install this app in advance Torque Pro to install the Android terminal.
(2) Start the Torque Pro.
(3) to move from the menu of the Torque Pro home screen to the "Settings" → "Plugins" → "Installed plugins ...", make sure that the "Torque PID plugin for MAZDA SKYACTIV-D" has been added .
(4) to move from the menu of the Torque Pro home screen to the "Settings" → "Manage extra PIDs / Sensors", and then select the "MAZDA SKYACTIV-D" from the "Add predefined set" in the menu. Make sure that the PID has been added.
(5) Torque you can use the added PID in the same way as standard PID of Pro.
Notes
Phenomenon that PID added from this plug-in from being deleted has been seen. In that case, please add again PID in how to use (4). If you will be frequently deleted, you are requested to contact the email address listed on this page. It has also been reported in the Torque Pro Forum (https://torque-bhp.com/forums/?wpforumaction=viewtopic&t=7290.0).
Support vehicles
It confirms the operation has in the CX-5 (KE / KF-based).
We receive operating report for the next SKYACTIV-D 2.2 / 1.5 equipped models.
Atenza (GJ system), acceleration (BM system), Demio (DJ system), CX-5 (KE / KF-based), CX-3 (DK system)
Corresponding PID
· Battery Estimated State of Charge (BATT SOC)
It displays the state of charge of the battery (estimated value).
· Battery Fluid Temperature (BATT TEMP)
It displays the temperature of the battery fluid.
· Boost Pressure (BOOST)
It displays the gauge pressure of the intake manifold.
· Brake Switch (BRAKE SW)
It displays the status of the brake switch.
Switch When on shows a 1, otherwise it shows 0.
· Brake Fluid Pressure (BFP)
It displays the brake fluid pressure.
· Charge Air Cooler Temperature (CACT)
It displays the temperature of the intercooler.
· Coupling Solenoid Duty Cycle (CUP SOL)
It displays the duty cycle of the solenoid of the coupling unit of the AWD system.
· Distance from Bumper to Target (DIST BMP TGT)
It displays the distance to the front of the object that has been measured in the near infrared laser sensor.
MRCC system equipped models is not supported.
· DPF Differential Pressure (DPF DP)
It displays the DPF differential pressure (the difference between the exhaust pressure before and after the DPF).
· DPF Lamp Count (DPF LMP CNT)
It displays the number of lighting times of the DPF warning light.
· DPF PM Accumulation (DPF PM ACC)
It displays the PM deposition amount estimated from such DPF differential pressure.
· DPF PM Generation (DPF PM GEN)
Engine speed, intake air quantity, and displays the PM generation amount estimated from the fuel injection amount.
· DPF Regeneration Count (DPF REG CNT)
It displays the DPF regeneration number of times.
· DPF Regeneration Distance (DPF REG DIS)
Displays the distance traveled from the previous DPF regeneration after completion.
· DPF Regeneration Distance 01 ~ 10 (DPF REG DIS 01 ~ 10)
It displays the previous mileage of history from the time of the DPF regeneration is completed until the next DPF regeneration start (the most recent 10 times).
Only SKYACTIV-D 1.5 supports.
· DPF Regeneration Distance Average (DPF REG DIS AVG)
Displays the average value of the distance traveled for each DPF regeneration is complete.
· DPF Regeneration Status (DPF REG STS)
It displays the status of the DPF regeneration.
During DPF regeneration represents 1, otherwise it shows 0.
· EGR A Valve Position (EGR A POS)
It displays the EGR A valve position.
EGR A is a Hot HP EGR.
· EGR B Valve Position (EGR B POS)
It displays the EGR B valve position.
In the case of SKYACTIV-D 2.2 equipped models, EGR B is Cooled HP EGR.
In the case of SKYACTIV-D 1.5 equipped models, EGR B is Cooled LP EGR.
· Intake Manifold Absolute Pressure (IMAP)
It displays the absolute pressure of the intake manifold.
· Intake Shutter Valve Position (ISV POS)
It displays the intake shutter valve position.
· Gear (GEAR)
It displays the gear of the AT.
· Lock Up (LOCK UP)
It displays the lock-up state of the AT.
When the lock-up represents a 1, otherwise it shows 0.
· Oil Change Distance (OIL CHG DIS)
It displays the distance the vehicle travels the oil data reset at the time of oil change from implemented.
The distance is incremented every 4 km.
· Torque Actual (TORQUE ACT)
It displays the engine torque.
· Total Distance (TOTAL DIST)
It displays the total travel distance.
· Transmission Fluid Temperature (TFT)
It displays the temperature of the transmission oil.